
Oxygen and Acetylene Regulator, Torch, and CO2 and Argon Regulator: The Complete Guide
, by عامر شوب, 6 min reading time

, by عامر شوب, 6 min reading time
Cutting steel without electricity, heating and loosening, or replacing CO2 and argon cylinders? A guide to oxygen and acetylene cylinders, torch setup, and cutting stainless steel for welding, with charts for all models.
There are some jobs that can't be done with a welding machine: cutting thick iron beams on-site without electricity, welding copper pipes, heating a rusted nut until it loosens, or burning weeds in the ground. This is where the torch comes in: an oxygen-acetylene torch, or a torch for a gas cylinder. And with every CO2 or argon torch, the tips and nozzles wear out and need replacing.
Acetylene burns with oxygen to produce an extremely hot flame. The welding torch is for welding and heating, while the cutting torch has an additional oxygen lever for cutting iron. The flashback arrestor (flame arrestor) prevents the flame from returning to the cylinder, and never operate without one.
It attaches to a small gas cylinder or a standard cylinder. For heating, loosening rusted bolts, light welding of copper pipes, applying bitumen, and burning weeds.
Nozzles and tips wear out with use. When welding becomes uneven or the gas no longer provides adequate protection, replace them before considering replacing the entire torch.
| Product | Note |
|---|---|
| Oxygen and acetylene flashback arrestor kit | 1 piece |
| Oxygen + copper acetylene flashback arrestor | 2 pieces |
| Oxygen + copper acetylene flashback arrestor | 2 pieces |
| Orange box oxygen welding torch | — |
| Prosket oxygen welding torch | With nozzles |
| Prescott welding torch | 3 nozzles |
| Yellow box welding torch | 3 nozzles |
| Red box oxygen cutting torch | — |
| Yamato oxygen cutting torch | — |
| Oxygen cutting nozzle | — |
| Product | Note |
|---|---|
| DILO DTFG1602 cutting torch | 165 mm |
| DILO DTFG1602 torch | — |
| DILO DTFG3603 torch | — |
| DILO DTFG3603 copper torch | — |
| JADIVER JDFG2602 cutting torch | 195 mm |
| Cutting torch | — |
| SF-178 long torch | For a cylinder |
| 915 torch | For a cylinder |
| FG-6 torch | For a cylinder |
| HS-509C torch | For a cylinder |
| KT-2108 torch | For a cylinder |
| M-60 torch | For a cylinder |
| QM628 torch | For a cylinder |
| ZD-306 torch | For a cylinder |
| Torch for a cylinder | — |
| Torch for a cylinder | — |
| Torch for a cylinder | — |
| Cylinder torch gas | 260 mm |
| Product | Note |
|---|---|
| CO2 welding torch | 5 meters |
| Kasper CO2 torch | 5 meters |
| ESAB welding torch | — |
| Long CO2 nozzle | — |
| Short CO2 nozzle | — |
| Short CO2 torch nozzle | 30 mm |
| Argon welding torch | 4 meters, 1 nozzle |
| Empty argon torch | — |
| Argon nozzle kit | 9 pieces |
| Long argon nozzle | 5 pieces |
| Short argon nozzle | 10 pieces |
| Ceramic argon nozzle | — |
| Argon torch nozzle holder | — |
| Argon torch insert | — |
| Torch plasma cutting nozzle | — |
| Plasma cutting nozzle | — |
Elbows, nipples, tees, and caps are welded onto pipe lines for food processing plants and water lines.
For light pipes and some other items, yes, but heavier work requires higher heat, and technicians usually use oxygen and acetylene.
When a lot of spatter builds up or the orifice widens. Clean it daily for a longer lifespan, and an anti-spatter spray helps.
Not sure which nozzle fits your torch? Take a photo and send it to us on WhatsApp.